Single Axis Positioner TS-X/P

Single Axis Positioner TS-X/P
Positional
Interface
Clean
Installation
"Gateway
Function"
Remote
Commands


Features

From single axis to 16 axis an optimal controller is available for each scenario.

With servo parameters and deceleration patterns pre-registered, robots are quickly and easily programmed.

Multi-functional and expandable, multi-axis controllers support up to 30,000 points or up to 100 programs.

Easy operability from design to evaluation programing is fast and efficient with our RCX-Studio Pro Support tool.


TS-X・TS-P
TS-S is a positioner type controller that only performs point trace. No program is needed.

Operating method: I/O point tracing / Remote command

Points: 255 points

Input power supply:AC100V / AC200V

Origin search method:TS-X : Absolute / Incremental

Origin search method:TS-P : Incremental / Semi-absolute


Additional Features

01 Design that allows a clean installation

Unified installation sizes Height and installation pitch are unified throughout the series. Units can be installed neatly within the control board.

02 Selectable I/O interfaces

Two RS-232C ports provided

Connect support tools
Intuitive operation supports controller design and maintenance.

Daisy-chaining
Two ports can be used to daisy-chain up to 16 units.

Communication commands
Easily understood ASCII text strings can be used to perform robot operations.

Selectable 100V/200V
  • The TS-X/P let you select AC100/200V as the power input. (The 20A model is 200V only.)
  • The TS-S2/SH is DC24V input.


A variety of I/O interfaces In addition to NPN and PNP, you can choose CC-Link, DeviceNetTM, EtherNet/IPTM, and PROFINET field networks.

Positioner interface Functionality has been condensed into an I/O interface with 16 inputs and 16 outputs. In addition to easy positioning, this also includes functionality that enhances interoperability with the control device.

Remote commands Numerical data can be directly manipulated by using the four-word input and four-word output areas. You can add new direct positioning commands to further unify the data at the control device.
Gateway function New types of connection are provided to reduce network costs. (CCLink, EtherNet/IPTM, and PROFINET are supported.)

03 Positional interface

"Positioner function" for easy positioning

You can easily perform positioning operations by specifying the number of a point that is registered in the data, and entering a start command.

A variety of output functions

The TS controller provides a variety of status outputs that are linked with positioning operations. By selecting and using an output appropriate for the scene, this can contribute to cost-saving measures such as making the steps of the control device's program more efficient or by reducing the peripheral equipment

Consecutive operation, linked operation

By specifying a branch destination, it is possible to execute positioning operations consecutively. Additionally, by specifying linked operation, operation with the branch destination can be executed while changing the speed without positioning stops; this allows control programming to be simplified and takt to be shortened.

Jog and point teaching functions are provided as standard

Jog movement and point teaching functions are provided as standard for input signals. By linking these with buttons of a touch panel etc., a simple teaching system can be constructed.

04 Remote commands

Ideal for unifying data management

Remote commands are functions by which the control device can directly handle data such as points and parameters using the word area of the field network. Numerical data can be operated directly by using the word area. This promotes unification of data management.

05 "Gateway function" -- a new way to connect

Decrease network cost

One controller equipped with a field network board can provide unified management of up to four I/O interfaces via a daisy-chain connection. This allows network cost to be decreased while enabling the same type of I/O control as when one board is installed for each unit. (CC-Link and EtherNet/IPTM are supported)

06 Daisy chain connection

No need to connect or disconnect cables during operation (up to 16 units)

From a single PC, handy terminal, or touch-panel display, it is possible to specify point data and parameters, perform operations, and monitor the status for up to 16 axes on daisy-chained controllers. For everything from design to maintenance, a connection to only the first controller is sufficient; any desired controller can be accessed simply by switching the station number, without having to connect or disconnect cables.

Communication commands

An easily handled command protocol using ASCII text strings supports a wide range of needs from data editing to operation and status monitoring. By daisy-chaining multiple devices, simple multi-axis control can be performed.

07 "KEYENCE PROTOCOL STUDIO Lite" serial communication settings software

By loading a TS settings file into PROTOCOL STUDIO Lite, communication settings and main communication commands can be registered automatically. Ladder-less data editing and daisy-chaining can be easily accomplished.

Contact for questions regarding PROTOCOL STUDIO Lite
Key Corporation

Daisy-chain connections (up to 16 axes)

Communication with the KV-L21V uses a Yamaha-made communication cable (D-sub type). By using daisy-chain connections, up to 16 axes can be managed together.

Automatic device assignment for each communication command

If the communication type is specified as cyclic, the desired information to be obtained is automatically stored in data memory.

08 Touch operator interface "Pro-Face" GP4000 Series

Connecting GP4000 Series made by Pro-face to Robot Positioner, TS-S2, TS-SH, TS-X, TS-P enables you to use a lot of functions as well as basic operations on Touch Operator Interface.

Free download of the program file from the Pro-face home page
http://www.proface.co.jp/

Can easily check a state and change settings.

If the communication type is specified as cyclic, the desired information to be obtained is automatically stored in data memory.

Can easily check a state and change settings.
  • Check the status (the current position, speed etc)
  • Basic operations such as Jog operation, inching operation, return to origin, error reset etc.
  • Set, edit, or back up point data and parameters
  • Check triggered alarms and detailed descriptions of alarm history
Supports 3 languages
  • Supports Japanese, English, and Chinese (simplified, traditional)

Specifications

Model TS-X / TS-P
100V AC input 200V AC input
Basic specifications
Driver model TS-X105 / TS-P105 TS-X110 / TS-P110 TS-X205 / TS-P205 TS-X210 / TS-P210 TS-X220 / TS-P220
Number of controllable axes Single-axis
Controllable robots TS-X: Single-axis robot FLIP-X series TS-P: Linear motor single-axis robot PHASER series
Power capacity 400VA 600VA 400VA 600VA 1400VA
Dimensions W58 × H162 × D131mm W70 × H162 × D131mm
Weight Approx. 0.9kg Approx. 1.1kg
Input power supply Control power supply Single phase AC100 to 115V +/-10% 50/60Hz Single phase AC200 to 230V +/-10% 50/60Hz
Motor power supply Single phase AC100 to 115V +/-10% 50/60Hz Single phase AC200 to 230V +/-10% 50/60Hz
Axis control
Control method Closed loop vector control method
Operating method I/O point tracing (Positioning operation by specifying point number) / Remote command
Operation types Positioning, merge-positioning, push, and jog operations
Position detection method TS-X: Resolver with multi-rotation absolute function TS-P: Magnetic type linear scale
Resolution TS-X: 16384 pulses/rev. or 20480 pulses/rev. depending on the robot TS-P: 1µm
Origin search method TS-X: Absolute / Incremental TS-P: Incremental / Semi-absolute
Points
Number of points 255 points
Point type setting (1) Standard setting:Set speed and acceleration in percent of the respective maximum settings.
(2) Custom setting: Set speed and acceleration in SI units.
Point teaching method Manual data input (coordinates input) , Teaching, Direct teaching
External input/output
I/O interface Selectable from the following: NPN, PNP, CC-Link, DeviceNetTM, EtherNet/IPTM, PROFINET
Input Servo ON (SERVO), reset (RESET), start (START), interlock (/LOCK) origin search (ORG), manual mode (MANUAL), jog motion - (JOG-), jog motion + (JOG+), Point number selection (PIN0 to PIN7)
Output Servo status (SRV-S), alarm (/ALM), operation end (END), operation in-progress (BUSY), control outputs (OUT0 to 3), Point number output 0 to 7 (POUT0 to POUT7)
External communications RS-232C 1CH
Power supply for brake DC24V +/-10% 300mA (prepared by the customer)
Safety circuit Emergency stop input, main power input ready output, emergency stop contact output (1 system: When the HT1 is used.)
Options
Handy terminal HT1, HT1-D (with enable switch)
Support software for PC TS-Manager
General specifications
Operating temperature / Operating humidity 0°C to 40°C, 35% to 85%RH (non-condensing)
Storage temperature / Storage humidity -10°C to 65°C, 10% to 85%RH (non-condensing)
Atmosphere Indoor location not exposed to direct sunlight. No corrosive , flammable gases, oil mist, or dust particles
Anti-vibration All XYZ directions 10 to 57Hz unidirectional amplitude 0.075mm 57 to 150Hz 9.8m/s2
Protective functions Position detection error, power module error, temperature error, overload, overvoltage, low voltage, excessive position deviation, overcurrent, motor current error
Protective structure IP20